Frigidaire Washer Dryer FARE4044MW User Manual

All about the  
Use&Care  
of your Dryer  
TABLE OF CONTENTS  
Important Safety Instructions..............................2-4  
Operating Instructions......................................5-12  
Care and Cleaning...............................................13  
Solutions to Common Problems.......................14-15  
Warranty ............................................................16  
Español ..............................................................17  
 
IMPORTANT SAFETY INSTRUCTIONS  
240 v Electric Dryer  
120 v Gass Dryer  
Groundiing type  
wall receptacle  
10-30R  
3-wire  
UL-approved service  
cord mustt be installed  
on electric drryerss (not  
provided wiith unit  
except those  
Do not, under  
any circumsstances,  
cut, remove,  
(fused 30 amp)  
or bypass the  
grounding prong.  
manufactureed forr sale  
in Canada).  
14-30R  
4-wire  
(fused 30 amp)  
Power cord with  
3-prong grounded plug  
Avoid re hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding  
prong from electrical power cord. Failure to follow this warning can cause serious injury, re or death.  
WARNING - RISK OF FIRE  
To reduce the risk of re, electrical shock, or injury to persons when using this dryer, comply with the basic warnings  
listed below. Failure to comply with these warnings could result in serious personal injuries.  
You can be killed or seriously injured if you don’t follow these Important Safety Instructions:  
PREVENT FIRE  
• Clean the lint screen before or after each load. The in-  
terior of the dryer, lint screen housing and exhaust duct  
should be cleaned approximately every 18 months by  
qualied service personnel. An excessive amount of lint  
build-up in these areas could result in inefcient drying  
and possible re. See Care and Cleaning.  
• Do not operate the dryer if the lint screen is blocked,  
damaged or missing. Fire hazard, overheating and  
damage to fabrics can occur.  
• Do not obstruct the ow of ventilating air. Do not stack  
or place laundry or throw rugs against the front or back  
of the dryer.  
• Do not spray any type of aerosol into, on or near dryer  
at any time.  
• Do not dry items that have been previously cleaned in,  
soaked in, or spotted with gasoline, cleaning solvents,  
kerosene, waxes, etc. Do not store these items on or  
near the dryer. These substances give off vapors that  
could ignite or explode.  
• Do not place items exposed to cooking oils in your dryer.  
Items contaminated with cooking oils may contribute to  
a chemical reaction that could cause a load to catch re.  
• Do not dry articles containing rubber, plastic or similar ma-  
terials such as bras, galoshes, bath mats, rugs, bibs, baby  
pants, plastic bags and pillows that may melt or burn.  
Some rubber materials, when heated, can under certain  
circumstances produce re by spontaneous combustion.  
• Do not use fabric softeners or products to eliminate  
static unless recommended by the manufacturer of the  
fabric softener or product.  
WARNING  
• Do not continue to use the dryer if you hear squeaking,  
grinding, rubbing or other unusual noises. This could  
be a sign of mechanical breakdown and lead to re or  
serious injury. Contact a qualied technician immedi-  
ately.  
• Failure to comply with these warnings could result in  
re, explosion, serious bodily injury and/or damage to  
the rubber or plastic parts of the dryer.  
FIRE HAZARD  
A clothes dryer produces combustible lint. The dryer  
must be connected to an outdoors exhaust. Regularly  
inspect the outdoor exhaust opening and remove any  
accumulation of lint around the opening and in the  
surrounding area.  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
PROTECT CHILDREN  
• ALWAYS disconnect the dryer from the electrical supply  
before attempting any service or cleaning. Failure to do so  
can result in electrical shock or injury.  
• Do not use any type spray cleanser when cleaning dryer  
interior. Hazardous fumes or electrical shock could occur.  
To prevent injury, do not reach into the dryer if the drum  
is moving. Wait until the dryer has stopped completely  
before reaching into the drum.  
• Do not allow children to play on or in the dryer. Close  
supervision of children is necessary when the dryer is  
used near children. As children grow, teach them the  
proper, safe use of all appliances.  
• Destroy the carton, plastic bag and other packing ma-  
terials after the dryer is unpacked. Children might use  
them for play. Cartons covered with rugs, bedspreads  
or plastic sheets can become airtight chambers.  
• Keep laundry products out of children’s reach. To pre-  
vent personal injury, observe all warnings on product  
labels.  
• Before the dryer is removed from service or discarded,  
remove the dryer door to prevent accidental entrapment.  
• Failure to comply with these warnings could result in  
serious personal injuries.  
PREVENT INJURY  
PREVENT INJURY AND DAMAGE TO THE DRYER  
• All repairs and servicing must be performed by an  
authorized servicer unless specically recommended in  
this Owner’s Guide. Use only authorized factory parts.  
• Do not tamper with controls.  
• Do not sit on, step on or stand on the dryer. Do not  
rest heavy loads on top. The dryer is not meant to sup-  
port weight.  
• Do not install or store the dryer where it will be ex-  
posed to the weather.  
• A thermal limiter switch automatically turns off the  
motor in the unlikely event of an overheated situation  
(electric dryers only). A service technician must replace  
the thermal limiter switch after correcting the fault.  
To prevent shock hazard and assure stability during  
operation, the dryer must be installed and electrically  
grounded by a qualied service person in accordance with  
local codes. Installation instructions are packed in the  
dryer for the installer’s reference. Refer to INSTALLATION  
INSTRUCTIONS for detailed grounding procedures. If the  
dryer is moved to a new location, have it checked and  
reinstalled by a qualied service person.  
• Failure to comply with these warnings could result in  
serious personal injuries.  
To prevent personal injury or damage to the dryer, the  
electrical power cord of a gas dryer must be plugged into  
a properly grounded and polarized 3-prong outlet. The  
third grounding prong must never be removed. Never  
ground the dryer to a gas pipe. Do not use an extension  
cord or an adaptor plug.  
CAUTION  
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of  
substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to  
warn customer of potential exposure to such substances. Included in this list are soot and carbon monoxide, both of  
which may be produced by the use of this product.  
ÍNOTE  
The instructions appearing in this Use and Care Guide are not meant to cover every possible condition and situa-  
tion that may occur. Common sense and caution must be practiced when installing, operating and maintaining any  
appliance.  
4
 
OPERATING INSTRUCTIONS  
Normal Operating Sounds  
You may or may not hear the following sounds from your  
new dryer:  
A. SUSPENSION ROLLERS The dryer drum is  
supported by a set of suspension rollers. At times  
there may be a thumping or rolling sound when the  
dryer starts. This may happen if the dryer has not  
been in use for a period of time, or after a heavy  
load has remained in the dryer drum for an extended  
period, creating a temporary at spot on the edge  
of the roller. The noise should dissipate as the dryer  
operates and the at spots smooth out.  
B. AIR FLOW SYSTEM Your dryer is equipped with a  
high volume air handling system. In some installations  
there may be some sounds associated with air  
movement throughout the dryer, including the air  
duct, blower, and exhaust system. This is normal and  
can vary with load size and type.  
A
D
C. GAS VALVE (Gas models only.) The ow of gas is  
controlled by electric solenoids. During operation there  
may be a clicking sound as the valve opens and closes to  
control the gas ow.  
C
B
D. GAS BURNER (Gas models only.) When the burner  
is operating, there may be sounds generated as the  
air ow mixes with the gas ame. This noise is normal  
and will only occur when the gas is ignited in the  
combustion tube.  
CAUTION  
Do not continue to use the dryer if you hear squeaking,  
grinding, rubbing or other unusual noises. This could  
be a sign of mechanical breakdown and lead to re or  
serious injury. Contact a qualied technician immediately.  
Operating Your Dryer  
1 Prepare load for drying.  
• Dry items of similar fabric, weight and construction  
in the same load.  
WARNING  
To reduce the risk of re, electric shock or injury to  
persons, read the IMPORTANT SAFETY INSTRUCTIONS  
in this Use and Care Guide before operating your dryer.  
• Separate dark items from light-colored items. Sepa-  
rate items that shed lint from those that attract lint.  
• Check for stains which may not have been removed  
in washing. Repeat stain removal process and wash  
again before drying. Dryer heat may permanently  
set some stains.  
• Place delicate or small items in a mesh bag.  
• Be sure buckles, buttons and trim are heatproof  
and won’t damage the drum nish. Close zippers;  
fasten hooks and Velcro®-like fasteners. Tie strings  
and sashes to prevent snagging and tangling.  
(Mesh bag not included.)  
5
 
OPERATING INSTRUCTIONS  
Operating Your Dryer, continued  
ÍNOTE  
2 Check that the lint lter is clean and in place.  
If a setting is not available for the cycle selected, the  
indicator will not light.  
• Adjustments made to a cycle will be remembered and  
recalled each time that cycle is selected in the future.  
To return to factory settings,  
press these two buttons at  
the same time and hold until  
the signal sounds.  
5 Start the cycle.  
3 Load the dryer and close the door.  
• Load items loosely. The average wet load will  
ll the drum 1/3 to 1/2 full. Items need room to  
tumble freely for even drying and less wrinkling.  
• If desired, place a dryer fabric softener sheet on  
top of the load at the beginning of the cycle.  
To save energy and time and avoid uneven drying  
and wrinkling, do not overload the dryer.  
• Close the dryer door. The dryer will not operate with  
the door open.  
• Push in or turn the cycle selector knob or press any  
option buttons to “wake” the dryer. You will hear  
three beeps to indicate dryer is ready to operate.  
• After making your selections, push in the selector  
knob to start the cycle. You will hear one beep before  
the drum begins to rotate.  
• When drying large items, dry only two or three  
items at a time. Fill out the load with small and  
medium sized items.  
• Select delay start to delay the beginning of the  
cycle, if desired.  
To add or remove items when the dryer is running,  
push in the cycle selector knob to pause the cycle  
and open the door. Opening the door with a cycle  
running will also pause the cycle. You will hear two  
beeps. Allow the drum to come to a complete stop  
before reaching inside. Add or remove the item,  
close the door and push in the selector knob again,  
continuing the current cycle.  
To cancel a running cycle, push in and hold the  
cycle selector until the dryer discontinues running.  
• A signal will sound at the end of the cycle if the  
chime option has been selected.  
• For delicate or very small loads, add two or three  
similar items to improve tumbling action.  
4 Select the appropriate cycle and settings for  
each load.  
ÍNOTE  
Over-drying can cause wrinkles, shrinkage, lint,  
harshness and a build up of static electricity.  
Turn the cycle selector knob in either direction to  
select the cycle desired.  
• The estimated drying time for Auto Dry cycles or  
the actual drying time for Timed Dry cycles will be  
displayed.  
• A suitable drying temperature, dryness level and op-  
tions will automatically be indicated for the cycle select-  
ed. See the “Dryer Settings Chart” for more details.  
To change the drying temperature and dryness  
level, press the temp or dryness level buttons to  
scroll to the desired settings.  
ÍNOTE  
If drying a single large or bulky item, such as a  
comforter, remove the item part way through the cycle  
and turn it “inside out” to maximize drying effectiveness.  
Place item back in dryer and re-start cycle.  
6 When the cycle ends, remove items immedi-  
ately and hang or fold.  
To select or delete an option, press options; then,  
while the indicator is blinking, press select. The  
indicator will light when the option has been se-  
lected. It will no longer be lighted when the option  
has been deleted.  
IMPORTANT  
Clean the lint lter after every load.  
6
 
OPERATING INSTRUCTIONS  
This manual covers many models and not all cycles, options, or features listed are available on every model. Console shown above  
for reference only. Your model may differ.  
Cycle Selection  
Auto Dry Cycles  
Turn the cycle selector in either direction to the cycle  
desired.  
Auto Dry cycles take the guesswork out of selecting the  
correct drying time for each load. Moisture sensing bars  
at the back of the dryer drum sense the moisture level of  
the load as it tumbles through the heated air. With Auto  
Dry cycles, the load will automatically be dried at the  
selected temperature to the desired dryness level. Auto  
Dry cycles save time and energy and protect fabrics.  
For best results  
Follow the fabric care label  
instructions on items  
to be dried.  
The estimated drying time will be displayed for about 5  
minutes. Then the outside of the display will light up in a  
circular track to indicate the drying time is automatically  
being determined by the sensors. When the load has  
reached the selected dryness level, it will continue to  
tumble during a cool down period. This helps reduce  
wrinkling and makes items easier to handle during  
unloading.  
Once a cycle is running, turning the selector knob to  
another selection will not change the cycle. If cycle  
selection change is attempted after the cycle starts, the  
indicator lights will ash and a signal will beep, but the  
original cycle will continue.  
1. initial  
2. calculating  
3. estimated  
ÍNOTE  
To change the cycle selection once the cycle has  
begun, push in and hold the cycle selector knob to  
cancel the current cycle, make the new selection and  
push in the selector knob again to restart the dryer.  
Drying time varies depending on size and dampness of  
load and fabric type. If the load is too small or almost  
dry, the moisture sensing bars may not detect enough  
moisture to continue the cycle and the cycle may end  
after a few minutes. If this occurs, select a Timed Dry  
cycle.  
Room temperature and humidity, type of installation and  
electrical voltage or gas pressure can also affect drying  
time.  
7
 
OPERATING INSTRUCTIONS  
Cycle Selection, continued  
casual  
Timed Dry Cycles  
Select this cycle to dry cottons, blends and permanent  
press items with a no-iron nish.  
WARNING  
normal  
FIRE HAZARD  
Select this cycle to dry everyday fabrics including  
cottons, linens and sheets.  
To avoid re hazard, do not use heat to dry items  
containing feathers or down, foam rubber, plastics  
similarly textured, rubber-like materials. Use a Timed  
Dry cycle and the air dry setting.  
heavy duty  
Select this Auto Dry cycle to dry durable fabrics such as  
work wear and overalls.  
refresh  
towels  
Select refresh to help remove wrinkles from clean and  
dry items that were not taken from the dryer at the  
end of the cycle, have been stored in crowded closets  
or drawers, or unpacked from luggage following a  
trip. It provides approximately 10 minutes of tumbling  
followed by a 5-minute cool down period.  
Select this cycle to dry heavy loads such as towels and  
non-rubber-backed bath mats.  
delicates  
Select this cycle to dry knits and delicates.  
bedding  
Select this Auto Dry cycle to dry bulky bedding items  
such as comforters, blankets, sleeping bags and  
parkas.  
quick dry  
Select this timed cycle to quickly dry a small load made  
up of just a few items. It provides approximately 20  
minutes of tumbling followed by a cool down period.  
jeans  
Select this Auto Dry cycle for drying an entire load of  
denim jeans.  
timed dry  
To manually select the drying time for any load, turn  
the knob to a numbered setting. Drying times from 60  
to 90 minutes are available. Moisture sensing bars are  
not active and dryer will continue to heat throughout  
the cycle until the nal cool down period. You will not  
be able to select a dryness level.  
kids wear  
Select this specialty cycle for drying kids clothing and  
baby wear.  
allergy  
Select this Auto Dry cycle where you wish to reduce  
allergens as you dry your load. Items prone to heat  
damage are not recommended for this cycle.  
8
 
OPERATING INSTRUCTIONS  
Cycle Settings  
For best results  
sanitize  
Recommended for durable fabrics and towels. Use this  
selection to remove harmful bacteria from your clothing  
or other items where sanitization is desired.  
Follow the fabric care label instructions  
on items to be dried.  
This option will kill 99.9% of bacteria with no carryover of  
bacteria between loads. A higher temperatures is required.  
Please check fabric care labels to prevent damage.  
Appropriate drying temperature, dryness level and  
options will automatically be displayed for each cycle. The  
settings can be modied before the cycle is started. Make  
modications based on load size, dampness and fabric  
type and durability. Modications for each cycle will be  
remembered and recalled each time that cycle is selected  
in the future.  
ÍNOTE  
Only sanitizing cycles have been designed to meet the  
requirements of NSF P154 protocol for sanitization  
efcacy.  
NSF Protocol P154  
Sanitization Performance of  
Residential Clothes Dryers  
To return to factory settings,  
press these two buttons at  
the same time and hold until  
the signal sounds.  
high  
Recommended for most cotton fabrics.  
normal  
Recommended for wrinkle free, easy care, lightweight  
fabrics and bulky loads.  
If changes are attempted after the cycle starts, the  
lights will ash and a signal will beep, but the cycle will  
continue.  
low  
Recommended for delicate fabrics.  
ÍNOTE  
air dry  
This setting (no heat) can only be selected with a timed  
cycle. The air dry setting tumbles the load without  
heat. Use this setting to dry items containing feathers,  
down, foam rubber, plastics or rubber-like materials;  
to refresh clothing, stuffed animal, pillows or blankets;  
and to dust draperies.  
To change the settings once the cycle has begun, push  
in the cycle selector knob to pause the cycle, make the  
new selections and push in the selector knob again to  
restart the dryer.  
Drying Temperature  
To change the preset temperature, press the temp  
button to scroll to the desired setting.  
Dryness Level (Auto Dry)  
To change the preset level, press the dryness level  
button to scroll to the degree of dryness desired.  
To protect your fabrics, not all temperatures are available  
with every cycle.  
To protect your fabrics, not all dryness levels are available  
with every cycle. If a dryness level is not appropriate  
for the cycle, it cannot be selected.  
The temperature selected for the cycle will be remembered  
and recalled each time that cycle is selected in the future.  
The dryness level selected for the cycle will be  
remembered and recalled each time that cycle is selected in  
the future.  
Select the normal dry level for most Auto Dry cycles.  
Occasionally a load may seem too damp or over-dried at  
the end of the cycle. To increase drying time for similar  
loads in the future, select high. For loads requiring less  
drying time, select low.  
Select damp for items you wish to partially dry before  
hanging or ironing.  
9
 
OPERATING INSTRUCTIONS  
Cycle Options  
To select an option, press options until the indicator  
for the desired option ashes, then press select. If an  
option is not available for a cycle, the indicator will not  
light. Follow the same steps to delete an option.  
ÍNOTE  
To change options once the cycle has begun, push in  
the cycle selector knob to pause the cycle, make the  
new selections and push in the selector knob again to  
restart the dryer.  
Occasionally, a setting and option in the same cycle will  
conict with each other, like sanitize temp and damp  
dry level. When this happens, the option selected rst will  
cause the conicting option to not be selectable.  
energy saver  
The energy saver option reduces the drying  
temperature a few degrees to save energy. In conjunction  
with automatic moisture sensors, cycle times will increase  
slightly, but overall energy usage will decrease.  
wrinkle release  
Select wrinkle release if the dried load might not  
be removed promptly at the end of the cycle. The dry  
load will continue tumbling without heat to help reduce  
wrinkling. When chime is selected, a beep will be  
heard periodically. The load may be removed any time  
during wrinkle release.  
shrink guard  
Select shrink guard to lower the initial drying  
temperature to protect fabrics from overdrying.  
chime  
A signal will sound at the end of the cycle (and  
periodically during wrinkle release) if this option is  
selected. The signal has an adjustable volume level or  
can be turned off.  
line dry  
Select this option to simulate hanging your laundry in  
a summer breeze combined with the wrinkle-releasing  
benets of tumble action. Since drying times are  
calculated with the dryer’s automatic moisture sensors  
and heat is radically reduced or eliminated, cycle time  
will be lengthened. As a result, depending on moisture  
content of load, overall energy consumption decreases.  
delay start  
Press delay start to select a drying time convenient to  
your schedule or during off peak energy hours. The delay  
time selected will be displayed and begin counting down  
when you push in the cycle selector knob to start the unit.  
ÍNOTE  
While counting down during delay start, you  
will notice your dryer periodically tumbling for a  
few minutes without heat to redistribute the load,  
maximizing load freshness.  
10  
 
OPERATING INSTRUCTIONS  
Dryer Settings Chart  
These Temperatures, Dryness levels and Options are available with the following cycles:  
temp  
sanitize  
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
high  
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
normal  
low  
9
9
air dry  
dryness level  
max  
9
9
9
9
9
9
9
9
9
9
9
9
high  
9
9
9
9
9
9
9
9
9
9
9
9
9
9
normal  
low  
damp  
options  
energy saver  
wrinkle release  
shrink guard  
chime  
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
line dry  
delay start  
9 = Available selections.  
= Cycle defaults.  
= Non-modiable presets.  
11  
 
OPERATING INSTRUCTIONS  
Other Features  
Drying Rack (on select models)  
Use the drying rack for items which should not be tumble  
dried. Insert the rack into the dryer drum, resting the back  
support on the moisture sensor bars and the front legs on  
the air grill.  
rear  
support  
front  
legs  
Place items to be dried on top of the rack, leaving space  
between items and not allowing them to hang over the  
sides or through the holes. The weight should not exceed  
10 lbs (4.5 kg). Select the air dry (no heat) setting for  
items containing plastic, foam rubber, rubber-like materials,  
feathers or down.  
moisture sens-  
ing bars  
When items are dry, remove the rack and store it in a con-  
venient location.  
ÍNOTE  
If your model did not come supplied from the factory  
with a drying rack you may order one.  
Control Lock  
To avoid having someone accidentally start or stop the dryer,  
press options and select at the same time and hold for  
10 seconds. If you attempt to activate the dryer while it is  
locked, the display will ash and error beeps will sound. To  
remove the control lock, press options and select again.  
Press and hold both for ten seconds  
to lock or unlock the controls.  
Estimated Time Remaining  
The initial drying time will be displayed for about 5 minutes  
after the start of a cycle. Then in auto dry cycles, the out-  
side of the display will light up in a circular track to indicate  
the estimated drying time is automatically being calculated  
by the sensors. Timed dry cycles continue with actual time  
remaining.  
Status Lights  
The following indicators may be lighted during the cycle:  
• clean lint lter  
• drying  
• cool down  
• wrinkle release  
• done  
Drum Light  
The drum light will come on whenever the door is opened  
to illuminate the drum during loading and unloading. Clos-  
ing the door turns off the light.  
Reversible Door  
Your dryer is equipped with a reversible door. The door can  
be hinged on the right or left side.  
ÍNOTE  
For step-by-step instructions on DOOR REVERSAL, refer to  
the Installation Instructions supplied with this dryer.  
12  
 
CARE AND CLEANING  
WARNING  
WARNING  
FIRE HAZARD  
To reduce risk of re or serious injury to persons or property,  
comply with the basic warnings listed in the Important  
Safety Instructions and those listed below.  
A clothes dryer produces combustible lint. The  
dryer must be connected to an outdoors exhaust.  
Regularly inspect the outdoor exhaust opening  
and remove any accumulation of lint around the  
opening and in the surrounding area.  
• Before cleaning the dryer interior, unplug the electrical  
power cord to avoid electrical shock hazards.  
• Do not use any type spray cleanser when cleaning the dryer  
interior. Hazardous fumes or electrical shock could occur.  
INSIDE  
• Clean the lint lter after every load. Lint build-up on the  
lter restricts air ow, which causes longer drying times.  
The lter is located at the bottom of the door opening. Re-  
move by pulling straight up. Remove the lint and replace  
the lter.  
• Occasionally a waxy build-up may form on the lint lter  
and/or moisture sensing bars from using dryer-added  
fabric softener sheets. To remove this build-up, wash them  
with warm, soapy water. Dry the lter thoroughly and  
replace. Do not operate the dryer without the lint lter in  
place.  
• If the dryer drum becomes stained from noncolorfast  
fabrics, clean the drum with a damp cloth and a mild liquid  
household cleanser. Remove cleanser residue before dry-  
ing the next load.  
IMPORTANT  
Clean the lint lter after every load.  
• Every 18 months an authorized servicer should clean the dry-  
er cabinet interior and exhaust duct. These areas can collect  
lint and dust over time. An excessive amount of lint build-up  
could result in inefcient drying and possible re hazard.  
OUTSIDE  
• Clean the cabinet with mild soap and water. Never use  
harsh, gritty or abrasive cleansers.  
• If the cabinet becomes stained, clean with diluted chlo-  
rine bleach (1 part bleach to 8 parts water). Rinse several  
times with clear water.  
• Remove glue residue from tape or labels with a mixture of  
warm water and mild detergent. Or, touch residue with the  
sticky side of the tape or label.  
• When cleaning chrome parts use a window cleaner with  
ammonia or mild soap and water.  
• Before moving the dryer, place a strip of cardboard or thin  
berboard under the front leveling legs to prevent damage  
to the oor.  
IMPORTANT  
Do not store or place laundry products on top of  
dryer at any time. They can damage the nish or  
controls.  
13  
 
SOLUTIONS TO COMMON PROBLEMS  
Common Drying Problems  
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric  
damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.  
PROBLEM  
POSSIBLE CAUSES  
SOLUTIONS  
PREVENTIVE MEASURES  
Greasy, oily  
stains  
• Fabric softener sheet.  
• Rub fabric softener stains with  
bar soap. Rinse and rewash.  
• Add a few bath towels to small loads  
for proper tumbling.  
• Some “silk-like” fabrics should be air  
dried.  
• Use proper drying temperature.  
• Place fabric softener sheet on top of  
load before starting the dryer.  
Lint  
• Overloading.  
• Overdrying causes static  
electricity.  
• Reduce load size and rewash  
using liquid fabric softener in the • Use fabric softener in washer or dryer  
nal rinse.  
• Do not overload dryer.  
to reduce static electricity.  
• Lint screen not clean when  
cycle began.  
• Lint is attached to “pills.”  
• Or, add a fabric softener sheet  
and tumble without heat.  
• Use lint brush or roller to remove • Check that lint lter is clean and in  
• Remove items when they are slightly  
damp to avoid overdrying.  
lint.  
place.  
Pilling  
• Overdrying.  
• Use a lint brush or shaver to  
remove pills.  
• Use fabric softener to lubricate bers.  
• When ironing, use spray starch or  
fabric nish on collars and cuffs.  
Turn items inside out to reduce abra-  
sion.  
(Fibers break  
off, ball up and  
cling to fabric.)  
Shrinking  
Wrinkling  
Temperature too high.  
• Overdrying.  
• Irreversible condition.  
• Follow fabric care label directions.  
• If shrinking is a concern, check load  
often.  
• Remove items while slightly damp and  
hang or lay at to complete drying.  
• Block knits into shape.  
• Overloading.  
• Leaving items in dryer after  
cycle ends.  
• Reduce load size and tumble at  
medium or low heat for 5-10  
minutes.  
• Do not overload dryer.  
• Remove items as soon as cycle ends.  
• Remove items immediately. Hang  
or fold.  
14  
 
SOLUTIONS TO COMMON PROBLEMS  
Avoid Service Checklist  
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences  
that are not the result of defective workmanship or materials in this dryer.  
OCCURRENCE  
POSSIBLE CAUSE  
SOLUTION  
Dryer does not start.  
Electrical power cord is not securely plugged in or plug Make sure the plug ts tightly in wall outlet.  
may be loose.  
House fuse blown or circuit breaker tripped.  
Reset circuit breaker or replace fuse.  
Make sure electrical line is not overloaded and the dryer is on a  
separate circuit.  
Thermal limiter tripped.  
Call authorized service person for replacement.  
Dryer runs but won’t  
heat.  
There are 2 house fuses in the dryer circuit. If 1 of the 2 Replace fuse.  
fuses is blown, the drum may turn but the heater will not  
operate. (electric models)  
Gas supply valve is not open (gas models).  
Check to make sure supply valve is open. See INSTALLATION  
INSTRUCTIONS for procedure.  
Dryer does not have enough air supply to support the  
See INSTALLATION INSTRUCTIONS.  
burner ame (gas models).  
LP gas supply tank is empty or there has been a utility Rell or replace tank.  
interruption of natural gas (gas models).  
Dryer should heat when utility service is restored.  
Drying cycle takes too  
long, outside of the  
dryer feels too hot or  
smells hot.  
Lint lter is clogged with lint.  
Make sure all lint has been removed from the dryer lint lter  
before starting each cycle.  
Exhaust duct requirements have not been met.  
Exhaust duct must be at least 4 inches in diameter and made  
of rigid or semi-rigid metal.  
When in place, the duct must have no more than four 90°  
bends and must not exceed length listed in INSTALLATION  
INSTRUCTIONS.  
Electric dryer is connected to a 208 volt circuit.  
Drying procedures have not been followed.  
Drying time will be 20% longer than drying on a 240 volt  
circuit.  
See “Operating Instructions.”  
Outside exhaust hood or exhaust duct may be clogged Clean out any obstruction.  
or restricted.  
High humidity.  
Use a dehumidier near the dryer.  
Do not overload. See “Operating Instructions.”  
Remove items as soon as cycle ends.  
See “Operating Instructions.”  
Excessive wrinkling.  
Dryer is overloaded.  
Items left in dryer too long.  
Insufcient sorting of items.  
Drying temperature too high.  
Follow fabric care label instructions.  
Scratching or chipping  
of the drum nish.  
Foreign objects such as coins, pins, clips or buttons  
are inside the dryer.*  
Always remove foreign objects from pockets before laundering.  
Remove objects from drum and restart dryer.  
Permanently attached items such as belt buckles,  
zippers and fasteners may be hitting the inside of the  
drum.*  
It may be necessary to sew a scrap of material securely around  
ornaments before drying to prevent scratching and damage to  
the dryer.  
*Drum damage caused by foreign objects or permanently attached items is not covered by the warranty.  
15  
 
MAJOR APPLIANCE WARRANTY INFORMATION  
For the applicable warranty period as set forth below, as measured from your original date of purchase, Electrolux will repair or  
replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and  
maintained in accordance with the provided instructions.  
Warranty Periods:  
• All parts — One year including labor  
• Wash tub — Functional life of the product (excluding labor)  
• Wash tub drive motor, non-cosmetic defects — Ten years (excluding labor)  
Exclusions  
This warranty does not cover the following:  
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.  
2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.  
3. Rust on the interior or exterior of the unit.  
4. Products purchased “as-is” are not covered by this warranty.  
5. Food loss due to any refrigerator or freezer failures.  
6. Products used in a commercial setting.  
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary  
household use or used other than in accordance with the provided instructions.  
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.  
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a  
part of the appliance when it is shipped from the factory.  
10. Service calls to repair or replace appliance light bulbs, air lters, water lters, other consumables, or knobs, handles, or other  
cosmetic parts.  
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage  
expense for service calls to remote areas, including the state of Alaska.  
12. Damages to the nish of appliance or home incurred during installation, including but not limited to oors, cabinets, walls, etc.  
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux  
parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse,  
inadequate power supply, accidents, res, or acts of God.  
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES  
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS  
PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR  
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE  
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND  
INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY.  
SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO  
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM  
STATE TO STATE.  
IF YOU NEED SERVICE  
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be  
required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be  
obtained by contacting Electrolux at the addresses or phone numbers below.  
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North  
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux  
authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty  
must be performed by Electrolux or an authorized service company. Product features or specications as described or illustrated are  
subject to change without notice.  
USA  
Canada  
1.800.265.8352  
Electrolux Canada Corp.  
5855 Terry Fox Way  
Mississauga, Ontario, Canada  
L5V 3E4  
1.800.944.9044  
Electrolux Major Appliances  
10200 David Taylor Drive  
Charlotte, NC 28262  
16  
 

Echo Trimmer HCA 266 User Manual
Estate Range TGP310T User Manual
Fedders Humidifier AC1A Series User Manual
Fisher Price Baby Swing 79618 User Manual
Fisher Price Baby Toy V2758 User Manual
Friedrich Air Conditioner CP10F10 User Manual
Frigidaire Range 316135928 User Manual
GE Clothes Dryer DBI333 User Manual
Giant Water Pump GP6140 4000 User Manual
Gitzo Camcorder Accessories GT3541LS User Manual